|
|
|
|
SynLube™ Lube-4-Life ® ... for Engines PERMANENTLY REPLACES Motor Oil
Product UsesSynLube™ Lube-4-Life ® ...for Engines is intended for use in all Automotive, Industrial, Marine, Aviation and Agricultural applications where the use of Petroleum or Synthetic Motor Oil is recommended by the OEM. (Original Equipment Manufacturer). SynLube™ Lube-4-Life ® ...for Engines can be used in all climatic conditions during all seasons because of its multi-viscosity SAE 5W-50 rating and an UHVI (Ultra High Viscosity Index) of VI=200. SynLube™ Lube-4-Life ® ...for Engines is a truly universal lubricant because it can be used in all Gasoline, Diesel, LPG or CNG fueled engines that are normally aspirated, turbo-charged or super-charged. SynLube™ Lube-4-Life ® ...for Engines is engineered to permanently replace conventional Petroleum Motor Oil in most severe operating conditions in high performance diesel and gasoline engines in highway, off-highway, farm fleets, inboard marine and piston engine aircraft applications. SynLube™ Lube-4-Life ® ...for Engines can be used in all applications where the use of any of the following SAE Viscosity rating is recommended by OEM:SAE 30, SAE 40, SAE 50, SAE 5W-20, SAE 5W-30, SAE 10W-30, SAE 10W-40, SAE 15W-40, SAE 10W-50, SAE 15W-50, SAE 20W-50 or SAE 5W-50 SynLube™ Lube-4-Life ® ...for Engines is NOT designed to be used in following applications:
Key Benefits
Additional Benefits
Product DescriptionSynLube™ is a synergetic blend of man-made liquid and solid chemically inert lubricants that are thermally stable from -65°F (-54°C) to over 500°F (260°C). The sub-micronic particles of Graphite, PTFE and MoS2 are colloidally suspended in a mixture of synthetic liquid lubricants. SynLube™ is a 100% fully synthetic, multi-grade, super premium, colloidal Sol lubricant. SynLube™
does not oxidize nor decompose like conventional Petroleum or Synthetic Motor Oils. It can
be therefore used, without oil changes, for up to 15 Years / 150,000 Miles or for up to SynLube™
Lube-4-Life ® ...for
Engines is backed up, if installed in NEW
vehicles, by our exclusive Limited Lubrication Performance
Warranty for up to:
Product PerformanceSynLube™ Lube-4-Life ® ...for Engines exceeds all of the following performance requirements:
Product Application
SynLube™
Lube-4-Life ® ...for
Engines INITIAL FILL is designed to be installed INITIAL FILL formula is used only the first time the product is installed. Use as much INITIAL FILL formula as is required to completely fill the crankcase. Verify Oil Level by checking the Oil Dipstick indication of FULL. Two Versions are available and are fuel specific:
SynLube™
Lube-4-Life ® ...for
Engines ADD OIL is designed to be installed ADD OIL is designed to be used ONLY as "make-up" or "Add Oil" it is NOT to be used for conventional lubricant applications! Two Versions are available and are fuel specific:
SPECIAL NOTE: In Diesel Engines which
are equipped with Cummins
Centinel
system use ONLY the INITIAL FILL
formula for a make-up oil into the reserve tank. Change Oil filter every 50,000 miles. DO NOT DRAIN OIL.
SynLube™
Lube-4-Life ® ...for
Engines SERVICE FILL It is to be used ONLY
in Gasoline fueled engines with very low oil consumption.
SynLube™
Lube-4-Life ® ...for
Engines UNIVERSAL is designed to be used for both; UNIVERSAL formula is less expensive and offers slightly improved fuel consumption over the combination of INITIAL FILL formula & ADD OIL formula, however the Engine wear protection is slightly reduced and the lubricant service life is limited to lesser of :
SynLube™
Lube-4-Life ® ...for
Engines FLUSH OIL is designed to be installed in Engines
which have been operated for long time on conventional
Motor Oil This FLUSH OIL formula has been designed to remove sludge, gum and varnish deposits caused by operation on conventional Petroleum Motor Oil. FLUSH OIL should be used with NEW OIL FILTER and TriMagnet for 200 miles
SynLube™
Lube-4-Life ® ...for
Engines BREAK-IN OIL is designed to be installed in Rebuilt Engines
which need some initial wear in due to imprecise
machining. BREAK-IN OIL should be used with NEW OIL FILTER and TriMagnet for
200 to 600 miles (or minimum of 5 engine run hours) prior permanent installation
of: SPECIAL NOTE: Do NOT USE this product in:
Modern manufacturing methods DO NOT require any break-in of new engines. Operate NEW OEM Engines on Factory Fill Motor Oil for minimum of 600 miles to maximum of 3,000 miles; then drain and install SynLube™ Lube-4-Life ® ...for Engines INITIAL FILL along with MicroGlass Oil Filter and TriMagnet.
Health and SafetyBased on available toxicological information, this product produces no adverse effects on health when properly handled and used. No special precautions are suggested beyond attention to good personal hygiene, including laundering oil-soaked clothing and washing skin-contact areas with soap and water. Also eye protection with suitable protective eyewear is suggested during handling and installation. In case of eye contact flush with plenty of water.
SynLube™ Lube-4-Life ® ...for Engines ADD OIL or UNIVERSAL is available in:
SynLube™ Lube-4-Life ® ...for Engines FLUSH OIL
SynLube™ Lube-4-Life ® ...for Engines BREAK-IN OIL
Pricing*
*) U.S. Retail Price includes FREE shipping by FedEx Ground Service in USA & Canada. *) U.S. Retail Price includes FREE shipping to Europe, Asia, Australia, South America by USPS Economy Air Parcel Service - Typical delivery time 5 to 15 days.
**) Special PRICING available on FLUSH OIL & BREAK-IN OIL if purchased together with SYN KIT for your vehicle. Ask for details.
Master Card & VISA Credit Cards are accepted on direct orders.
|
|
Send mail to synlube@aol.com with questions or comments about this web site.
Lube-4-Life?
is a Registered Trademark of SynLube, Inc.
|